Energy Sector Thread - Operators, Engineers, Technicians Et Al

[K74T]

[Joshie23]

http://www.ppgpl.com/2015/vacancies/REC ... VISOR.html

[sMASH]

what goin on up pt lisas? i hear a lot of plants are off line, ngc instructed to come down.

[eitech]

Aum downstream was suppose to have a small outage this week but due to the impending deep gas curtailment( mth end october 3 weeks into nov) we holding on till then. Not sure if plants here will operate at reduced rates or come down flat. Thatz d word on the plant

[rmrunner]

Saw this in papers in case anyone interested

[sMASH]

Aum downstream was suppose to have a small outage this week but due to the impending deep gas curtailment( mth end october 3 weeks into nov) we holding on till then. Not sure if plants here will operate at reduced rates or come down flat. Thatz d word on the plant

i hear a set down, MeOH and NH3. heard m5 had reformer issues too.

[demented]

what goin on up pt lisas? i hear a lot of plants are off line, ngc instructed to come down.

CNC was instructed to shut down on Sunday by NGC. However strangely M2 start up at the same time.

[De Dragon]

what goin on up pt lisas? i hear a lot of plants are off line, ngc instructed to come down.

CNC was instructed to shut down on Sunday by NGC. However strangely M2 start up at the same time.

Deep gas cuts at month end due to NGC upstream suppliers maintenance activities. Several plants are taking outages so that the ones remaining on line can have full(ish) supply. M5 blew some tubes, hence M2 being placed on line, can't say what is the issue with CNC.

[rmrunner]

Tubes again. One thing by now all them reformers suffered damage

[sMASH]

Tubes again. One thing by now all them reformers suffered damage

"Pressure dies buss pipe." - unknown

"Cycling of pressure does buss reformer and boiler pipe." - sMASH

[De Dragon]

Tubes again. One thing by now all them reformers suffered damage

"Pressure dies buss pipe." - unknown

"Cycling of pressure does buss reformer and boiler pipe." - sMASH

M4 never burst any tubes

[sMASH]

Tubes again. One thing by now all them reformers suffered damage

"Pressure dies buss pipe." - unknown

"Cycling of pressure does buss reformer and boiler pipe." - sMASH

M4 never burst any tubes

time longer than twine... and stay away from putting goat in ur mouth
.

[De Dragon]

Tubes again. One thing by now all them reformers suffered damage

"Pressure dies buss pipe." - unknown

"Cycling of pressure does buss reformer and boiler pipe." - sMASH

M4 never burst any tubes

time longer than twine... and stay away from putting goat in ur mouth
.

Just stating facts bro. M4 is not, or should not actually, be an anomaly in how to manage a hydrogen Reformer.

[sMASH]

u cant tell which tube will burst, and rolls royces tend to be well built... lol.

[De Dragon]

u cant tell which tube will burst, and rolls royces tend to be well built... lol.

Actually you can with proper monitoring and checks. Cycling temps/pressures do reduce tube life, but usually it is operating outside of parameters that gets you.

[DreamWeaver]

Tubes again. One thing by now all them reformers suffered damage

"Pressure dies buss pipe." - unknown

"Cycling of pressure does buss reformer and boiler pipe." - sMASH

M4 never burst any tubes

If i recall, when the govt finally give MHTL back gas to run M4 after they had sent home workers last year, M4 was blowing tubes every week. They kept shutting down, plugging tubes and starting back up until eventually they realise it didnt make sense. That's when they negotiated to have the M4 gas used on M2 instead until M4 finished its TAR this year.
On a related note, M2 only running right now because M5 down. When M5 start back, M2 going offline unless Denovo come online to supply it in time.

[sMASH]

the germs building plant like if it coming ready make... fleckers not easy.

[De Dragon]

Tubes again. One thing by now all them reformers suffered damage

"Pressure dies buss pipe." - unknown

"Cycling of pressure does buss reformer and boiler pipe." - sMASH

M4 never burst any tubes

If i recall, when the govt finally give MHTL back gas to run M4 after they had sent home workers last year, M4 was blowing tubes every week. They kept shutting down, plugging tubes and starting back up until eventually they realise it didnt make sense. That's when they negotiated to have the M4 gas used on M2 instead until M4 finished its TAR this year.
On a related note, M2 only running right now because M5 down. When M5 start back, M2 going offline unless Denovo come online to supply it in time.

Lemme rephrase "M4 never burst any tubes while I was there"

[sMASH]

Mine too, it WAS the rolls royce till after. m3 had boiler tube, buss out tube sheet, and curl up on the bull head and ting.

[De Dragon]

Mine too, it WAS the rolls royce till after. m3 had boiler tube, buss out tube sheet, and curl up on the bull head and ting.

What about when the hole appeared in the shell of the BFW pre-heater? 140 bar water straight up in the air yo!

[sMASH]

i wonder if u was there when 'ah man' buss de refining column?

[De Dragon]

i wonder if u was there when 'ah man' buss de refining column?

How he do that? Isn't the relief valve on the overhead vapour line set at 5.5 barg?

[sMASH]

well, apparently if u jam it with nitrogen purge, the little weak spots may fall victim. a guy with a dent on a strong arm.
the max range on the overhead PT was 2barg. it became the fattest part of the N2 header.

[De Dragon]

well, apparently if u jam it with nitrogen purge, the little weak spots may fall victim. a guy with a dent on a strong arm.
the max range on the overhead PT was 2barg. it became the fattest part of the N2 header.

Some men doh facking learn Basic, basic monitoring and trending lapse.

[rmrunner]

Heard they looking for ppl again cause they might finish their gas line soon.

[PapaC]

Gas contract signing boy. CNC3 live with a conference. Nutrien, formerly PCS.

[sMASH]

no more roman candles in the skyline... whey..

[car]

Anyone knows what’s the average salary for a technician working 14 days on /off on one of those offshore platforms for the International companies like bp,shell,bg?

Can anyone put their views/experience about working on the above situation? Pros and cons besides getting horn.

[eitech]

Anyone knows what’s the average salary for a technician working 14 days on /off on one of those offshore platforms for the International companies like bp,shell,bg?

Can anyone put their views/experience about working on the above situation? Pros and cons besides getting horn.

Lol. If you know u cant or can take horn thats ur answer right there.

[Cantmis]

Anyone knows what’s the average salary for a technician working 14 days on /off on one of those offshore platforms for the International companies like bp,shell,bg?

Can anyone put their views/experience about working on the above situation? Pros and cons besides getting horn.

Shell bought out bg