Amp suggestions

[Crazy Chris]

Arite tuners jus looking for a lil feed back here. I wana run a very simple system all pioneer 2 6" in the doors 2 6x9 on the dash and one single 12" for bass. Can i use one amp for this? And if yea what brand and watt wud u rcommend. Any info wud be appreciated.

[OffshoreMarketing]

plenty good amps around u can let us know what kind of 12" and speakers so u can get something to match them

skar audio is my recommendation have a few diff models of four channels to choose from

[SQ Audio]

ZAPCO ST-5D

5 Channel Full range class D
Power@2Ω:4x100watts+4Ω:1x350watts
RMS Rated Power @ < 0.05%THD
Power @ 2Ω:4x100watts+1x350watts
Power @ 4Ω:4x75watts+1x350watts
Bridged@4Ω:2x200watts+1x350watts


-Class-D bridgeable 12V amplifier
-5/3 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-18dB octave crossover slope
-Variable FULL / LP / HP Electronic Crossover -Variable bass boost
-RCA Signal input and output connectors
-4-way protection circuitry
-thermal / over current / speaker short / DC
-Tested voltage & THD: 14.4V & less than 0.05%
-Dimensions in Inches : 6.7(W) x 2.2(H) x 10.5(L)

[shake d livin wake d dead]

budget?

[tdavies]

rockford fosgate p4004 brand new -$2000
extremely good amp

701-4855

[Sully]

rockford fosgate p4004 brand new -$2000
extremely good amp

701-4855

Not going to work. He needs a 5ch amp.

[MonsterPower]

there is an alpine 5 ch in the classifeds that wi,ll work great in that application

[tdavies]

rockford fosgate p4004 brand new -$2000
extremely good amp

701-4855

Not going to work. He needs a 5ch amp.

actually it can

channel 1/2 can be used for the speakers
unbridged imp is 2 ohm max

channel 3/4 can be used for the sub
bridged imp is 4 ohms

[Sully]

Depending on the power handling capabilities of the speakers, the staging will be way off. Without fader control, it's going to be very difficult to fix.

[CleanAudio]

I recommend Powerbass 5 Channel Amp ....Good Amp and not too Costly.

4 ohms: 50 watts x 4 chan. + 200 watts x 1 chan.
2 ohms: 100 watts x 4 chan. + 400 watts x 1 chan.
4 ohm Mono: 200 watts x 2 chan. + 400 watts x 1 chan.

1400 watts Peak Power

Total Harmonic Distortion:
<0.05%

Frequency Response:
20Hz~22,000Hz

S/N Ratio:
>94dB

Damping Factor:
>150

Input Sensitivity:
0.5 - 4.0 volts

Crossover Slope:
12dB

High-Pass Crossover Freq (Hz):
40Hz~250Hz

Low-Pass Crossover Freq (Hz):
40Hz~250Hz

Variable Subwoofer EQ:
0/+18dB

Subwoofer EQ Frequency:
40Hz

What are the Ohms of the speakers btw?

[DjDaniel]

If you on a low budget. The 6' and the 6x9's can run on the deck's power (HPF) and just run the 12' on a monoblock. Else the 5 channel is a good idea.