Amp to push 4 Beyma Pro10mi

[Richramba]

Handles 350 watts AES & 700 watts program power

Thanks

[speedmelter]

PM user casperbrown

[Richramba]

thanks speedmelter

[rishadneil]

have a 4ch power acoustik.... waz pushin 4 10 rcf... pm me if interested

[speedmelter]

have a 4ch power acoustik.... waz pushin 4 10 rcf... pm me if interested

which model PA is this?

[amp.fanatic]

what ohmage de speakers are??

[Richramba]

its 4 ohm each speaker @ amp.fanatic

[speedmelter]

get a 2 ch amp thats 2000WRMS at 4 ohm, minimum

[amp.fanatic]

use a 2000x us amps 2000rms@12 at 4ohm

[Richramba]

You know around how much it goes for maybe you have a link ..
Thanks

[Richramba]

Should I get the 8 ohm or the 4 ohm ? I don't really know a lot about it any help will be good

[speedmelter]

get the 4 ohm version, if you get the 8 ohm version you would need a really powerful 4ch and thats harder to come by than a powerful 2ch.

if you go 8 ohm, the first amp in here looks nice viewtopic.php?f=8&t=507683

or you can look for the us amp mentiond... those are all used doh.. they dont make them again

[amp.fanatic]

if u buy de 8ohm speakers u can run de us amps 2000x it goes for around $5000 if ur speakers are 4ohm u can use de stetsom as stated or de us amps usa2000 dats 2000rms@12 at 2ohms

[Team2lo2flo]

You can also look at the Stetsom 2k5es 2ohm or 3k7es 2ohm

[Richramba]

Ok I will look into it they don't sell it where am at only on eBay

[SQ Audio]

Z 400.2 $6305.00

Stereo, 4 ohms: 2 x 400 Watts
Stereo, 2 ohms: 2 x 670 Watts
Bridged, 4 ohms: 1 x 1340 Watts
T.H.D. + Noise: <0.05% @ 4 ohms

-Class-AB bridgeable 12V amplifier
-2/1 channel bridgeable 12V amplifier
-Stable into 4 ohms bridged or 2 ohms stereo load
-PWM MOSFET power supply
-Variable input sensitivity
-18dB octave crossover slope
-Variable FULL / LP / HP crossover
-Variable bass boost
-Signal input and output RCA connectors
-Multi-way protection circuitry
-(thermal / over current / speaker short / speaker DC protection)
-Tested voltage & THD: 14.4V & less than 0.05% THD at rated power
-Operating voltage : DC10V~15.5V power input
-Wired remote control (optional)
-Dimensions in Inches : 7.5(W) x 3(H) x 20.25(L)

[Richramba]

I was looking to the Lanzar OPTI250X4 Optidrive 2000 Watt 4 Channel Competition Class Mosfet Amplifier
Lanzar

Anyone know how I will have to wire the speakers ?

[Richramba]

or even
Hifonics Zeus ZRX2000.4 2000 Watt 4-Channel A/B Car Audio Amplifier

[ward one]

i have used both of the amps listed above. none of which can play 4 10's properly. maybe 4 8" bt not 4 10's.

just look at the fuse rating- 120 amps on the hifonics and 200 amps for the lanzar.

look in the the us amps and the old skool ppi's these amps have been tried and tested to work for this application.

the us amps usa 2000 or 2000x goes for around $5000, the ppi 21400 for around $4000 and the ppi pcx2400 for around 4500

all of which performs really good

[southside connections]

dd s2b?

[noelsook]

get the 4 ohm versions.....wire them to 2 2ohm load and drop them on the Lanzar Opti 1600x2.....or get the 8 ohm version wire them to 2 4 ohm load and run the same amp at 4 ohm stereo.....based on specs it should be atleast 800 rms per channel.....http://www.ebay.com/itm/NEW-LANZAR-OPTI ... 5af1f5d6b3