Page 1 of 1

D15B 3 stage vtec ecu wirin

Posted: April 8th, 2006, 2:23 am
by civcdrvrinwrx
i lookin for the wirin diagram for a D15B 3 stage vtec.
one that shows not only the vtec solenoid wires but also the vtec monitor wires. looked in the helms96-2000 and it was a waste of time.
KES WHERE R U?

Posted: April 8th, 2006, 2:25 am
by civcdrvrinwrx
cleriq boss i waitin patiently.
NO PRESSURE OR NETHING.

Posted: April 8th, 2006, 7:50 am
by kes_vtec
what is the number of ur ecu

Posted: April 8th, 2006, 2:24 pm
by Clerique
^P2J

Posted: April 8th, 2006, 10:50 pm
by civcdrvrinwrx
^^^what he said i guess

Posted: April 10th, 2006, 8:45 am
by kes_vtec

Posted: April 10th, 2006, 9:52 pm
by civcdrvrinwrx
a kes thanks a lot dred :D :D :D :D :D :D this is extremely helpful. i goin to frame this horse u wudnt believe how hard it was to get this.
thanks a million but i not seein two wires goin to the ecu for each of the two solenoids. i seein one wire for both :? :? u feelin to help me wire it or wa.
ill pay u. :mrgreen:
no seriously ill pay u for the time. u just tell me when and where. check ure pm. call me nah

Posted: August 17th, 2009, 11:12 am
by rudeboye_r
kes i have the same problem can you help i put a 3 stage in a non vtec 96 civic and it doesn seem to go into vtec it is real lazy catching my ass to pass 4000. let me know if you help.

Posted: August 17th, 2009, 6:08 pm
by Sky
civcdrvrinwrx wrote:a kes thanks a lot dred :D :D :D :D this is extremely helpful. i goin to frame this horse u wudnt believe how hard it was to get this.
thanks a million but i not seein two wires goin to the ecu for each of the two solenoids. i seein one wire for both :? :? u feelin to help me wire it or wa.
ill pay u. :mrgreen:
no seriously ill pay u for the time. u just tell me when and where. check ure pm. call me nah


If it's the same kinda P2J like mine it should be obd2a
Image

You used the ecu for that engine right? If for some reason the swapper didn't use the 3 stage harness then you'll have to run the wires yourself.

rudeboye_r, did YOU use the P2J ecu that came with the engine? If you did then you can just wire the 1st solenoid to ign on so you can use your 16 valves, because from the rpm it sounds like you can't leave your 1st stage. IF you really have a nonvtec ecu then do the above and take strain without vtec :lol:

Posted: August 20th, 2009, 12:24 pm
by rudeboye_r
it is a p2j j62 auto but i have a gearbox how do i identify the 1st is it the green and yellow wire or red ?

Posted: August 20th, 2009, 3:04 pm
by Sky
The green/yellow is for the 1st solenoid from stage 1 to 2. The red is for mild cam to wild, stage 2 to 3.

Re: D15B 3 stage vtec ecu wirin

Posted: June 26th, 2010, 7:56 pm
by Oyabun
You get through with wiring???? I have the same xxing problem