Forums

jackal

Paid $95.40 to clear Samsung Tab S6 today.

jackal

Who have shims for the toyota diesel engines, the 37mm ones for the valve and camshaft adjustments?

jackal

Ah like it, ah go build one from teak later in the year.

jackal

So I went in the diff, the needle bearing was the culprit. A few of the needles had froze in position and the inner CV was wearing its diameter. So I had to change the bearing and the CV. This is what the bearing looked like. Needle Bearing.jpg Well, since I had to remove the entire diff, I went dow...

jackal

Not that dude.

The one that make the ends of the brake line that will connect to the master cylinder or the calipers etc.

jackal

Looking for a brake flaring tool kit in south.

Laughlin don't have, Allied have the very expensive one.

Who in south might have a reasonable price one?

jackal

telfer wrote:
jackal wrote:
Rayden6 wrote:2RZ or 3RZ

The issue is the mating on the engine to the rest of the drive train.

I adapter plates are readily available, it would be awesome!

That’s simple.....bell housing for R151 to 3rz easily available

That sounding like a plan if I f/up the engine.

jackal

Wanna change out the clutch in my LN167.

I want to get something with more grip for the mud, mine does slip sometime in the mud, no copper. must be able to "ride it".

Who down hear have clutch and pressure plate kits for sale.

jackal

I believe it is a 7.5" in the front

jackal

Once I open the front diff and is nothing major, and ah get the lunchbox, i go sneak it in the front. Will continue to look for the LSD carrier for the back after the holidays.

jackal

I have a old one that scrap out that the previous owner give me, i will post it when i come off work.

jackal

I am only allowed this one for now, full 4X4, LSD in the back and lunchbox in front with free wheel hubs.

Working on the surf to get it at least to full 4X4 and hold off there.

jackal

I eh go lift mine the wife will complain. I have a 2" spacer kit to put on about three years now, it still pack down.

jackal

If the carrier is the same I would have to swap out the crown wheel and pinion.

jackal

Looking for one for my surf KZN185, 1998 I think, 1KZT, intercooled, not sure of the tranny. I know it is a 3 speed with overdrive. If things goes right should have a lunchbox in the front by end of the month. Have to go in and do some work on a shaking CV joint. Should have the CV and needle beari...

jackal

We sent one on an offshore platform to feed the dog.

He couldn't find the dog.

jackal

I was on block release from school. We send one of the interns with a wheelbarrow to warehouse and told him to ask for a 300 lb gauge. The attendant had a ball with him. He come back cussing we.

jackal

Rayden6 wrote:2RZ or 3RZ

The issue is the mating on the engine to the rest of the drive train.

I adapter plates are readily available, it would be awesome!

jackal

I think it is a 4 - 1, 41 crown and 10 pinion.

Will confirm when i open it up.

jackal

Looking for one for my surf

jackal

Wanna know what is the ratio of the 3.0L LSD differential ratio, the 2015 and before model?

What is the ring gear size?

jackal

based on what u typed something doesnt seem right , no way a 29 or 3hz tuning wud use such a short port for such a small cuft double check ur calculations with this https://www.the12volt.com/caraudio/boxcalcs.asp also - common local pvc pipe is never 2" or 4" , 4" is actually 4.3&quo...

jackal

That size enclosure it's better to go sealed. Port noise is gonna be terrible with that small port. May sound okish at low excursion. The volume is very very close to what the speaker spec sheet recommends for a sealed box. As it is right now, it sounding better, I getting a better "roll"...

jackal

Crossectional view.jpg So, the rain falling today, I could not go anywhere, so I went in and change the port length. I had 14" long 2" ports, so based on the WinISD Pro, for a 1.67 cu/ft box, I would need a 2.35" long port for a 35hz frequency and about 4" for a 29hz frequency. ...

jackal

It is a pretty good engine. It comes in cable throttle or electronic throttle. Power range from about 138 to 145 for the intercooled versions. I think that is has a lot of low-end torque. The big cons, it have an aluminum cylinder head, and any defect in the cooling system, it will damage it. A used...

jackal

From what I see on Facebook, he dam real good!

jackal

I will check it out.

jackal

Anybody out there that does this type of repair with taking out the entire console or windscreen?

jackal

The more I reading up on this thing, the more I realize how little I know.

jackal

Right now i trying to optimize the music in my van, the bass at the moment.

Forums

Search found 703 matches

Re: Cellphone Import Tax

Re: Toyota Surfs,Hilux and 4X4s.

Re: Welding & Fabrication

Re: Toyota Surfs,Hilux and 4X4s.

Re: Brake Flaring kit

Brake Flaring kit

Re: Toyota Surfs,Hilux and 4X4s.

Clutch Options

Re: Hilux rear differential.

Re: Toyota Surfs,Hilux and 4X4s.

Re: Hilux rear differential.

Re: Toyota Surfs,Hilux and 4X4s.

Re: Toyota Surfs,Hilux and 4X4s.

Re: Hilux rear differential.

Re: Hilux rear differential.

Re: Is a different kinda dotish it have out here?

Re: Is a different kinda dotish it have out here?

Re: Toyota Surfs,Hilux and 4X4s.

Re: Hilux rear differential.

Re: Hilux rear differential.

Hilux rear differential.

Re: Sub Woofer box tuning.

Re: Sub Woofer box tuning.

Re: Sub Woofer box tuning.

Re: Toyota Surfs,Hilux and 4X4s.

Re: Upholstery Repair

Re: Upholstery Repair

Upholstery Repair

Re: * THE OFFICIAL HOME THEATER & AUDIO THREAD

Re: * THE OFFICIAL HOME THEATER & AUDIO THREAD