Forums

trini iceman

And after all the big fight, OP hasn't even responded. LOL I thought it down by you already. Sorry OP. I guess hesitation and power loss may not mutually exclusive. Power loss cause hesitation or hesitation seen as power loss. Possibilities are: Input screwing up tps, cam/ crank etc. Output screwin...

trini iceman

nightman22 wrote:
trini iceman wrote:What your fuel trims look like?

Sorry I don't what fuel trims is

Well you have my contact. When you're ready

trini iceman

You can contact me at 3981404

trini iceman

OK if that's the path, we have to consider that modern cars with high compression, high pressure multiple port injection burn leaner so building heat to aid in combustion is not much of a challenge as it was in carbureted. I'm not trying to prove anyone wrong but I'm working with a paragraph on a sc...

trini iceman

Start simple first. A loss of power problem that exist when the engine is cold only is most likely electrical, spark plugs, coil packs etc. If it occurs even after the engine has heated up, it's usually air or fuel. Check fuel filter/s and air filter first then go on to the above mentioned items. B...

trini iceman

What your fuel trims look like?

trini iceman

You can get me @3981404

trini iceman

You can get me @3981404 for assistance

trini iceman

A cheap JOBD compatible tool will work. Check eBay.

trini iceman

Sounds like misfire. Won't know the type till I test.

trini iceman

Interested 3981404

trini iceman

You can reach me at 3981404 to sort this.

trini iceman

You use treatment?

trini iceman

You can get me @3981404

trini iceman

originalbling wrote:Where are you guys getting ac work done? Getting a rattle when ac is on at low speeds only. need it diagnosed.

seem hard to find a reliable mazda mech

You can be me @3981404

trini iceman

Contact us @3981404

trini iceman

huud wrote:
trini iceman wrote:I can repair these 3981404. Won't kill you with price.

Where you located i need mine fix ck4 lancer

200-300 depending on what has to be done

trini iceman

T27 wrote:my mazda 3 2010 model is cutting of on the first start and starts back normal on second start this happened after I I cleaned the throttle body please help me out I changed plugs oil filter use liquid moly injector cleaner to put in gas tank

You can get us @3981404

trini iceman

Intelligent Power Distribution Module (fuse box with a brain)

trini iceman

Sounds like battery or ipdm

trini iceman

So reporting this as the problem has re-occurred and I've lost the number for the guy that assisted me from here. Hey guys/girls I have a mazda 6 2003 I believe that won't start. Been through 2 mechanics and they can't find the problem. One mentioned it may be built in immobiliser malfunctioning. I...

trini iceman

Control modules are behind the center behind ac controls, remove the side trim to expose them

trini iceman

Any one had issues with the factory immobilizer. Its a company vehicle but still under warranty. I was informed that it spent two weeks by Massey and they could not or did not fix the issue. NISSAN Navara not the NP. Many times the vehicle would not get to click the starter. It's almost a game comi...

trini iceman

OK. They probably getting a "no communication" when they scan. I'm not sure if they'll want to flash the used module but they will be able to install.

trini iceman

I never heard that a module locked up. Trying to figure out if there's a collision detection.

trini iceman

Power, gnd and signal. Find those for the tach.

trini iceman

Are the seatbelt locks the same length?

trini iceman

You had any collisions, repairsvdone battery replaced?

trini iceman

Did they give a code of just told you it locked up?

trini iceman

Hey everyone.... I'm having a bit of a problem with my p11's transmission I believe. When in the 4th gear on the highway it starts to vibrate a lot on light throttle... I've looked at the speedometer whilst it was happening and noticed my rpm was below 1000..... is the low rpm in that gear the prob...