Forums

R. Hertz33

Still trying to confirm whether it safe or not though...cuz i see one or two other riders

R. Hertz33

Caura is actually a nice run, not too much strays but u have to be aware around the corners, early sunday morn is easy though. But alot of ppl warned me that its not safe, so i dont go anymore ssince i ride solo. But if u get a padnah yea

R. Hertz33

You could buy the entire fitting where the drain is so the right sode would look like left side of thats the problem

R. Hertz33

Thanks for the info, will do

R. Hertz33

Hey guys, So as up top, i have one of those, just bought it and it has a demonic wobble around 55kph. Need some advise please. Research thus far seems to point towards front bearings and also a knuckle seal. I can get the bearings but where can i get the knuckle seal. Also open to recommendations fo...

R. Hertz33

[img]http://www.trinituner.com/mobile-gallery/5f3e9c0bf4780c260306f29be7cb0d55.jpg[/img]

R. Hertz33

A good entry level fuji Nevada will run u about 3.5k, but try to get last year's model as it would be a higher spec for same price, if u plan on spending more than 3.5k then the next step is about 6k anything in between isn't really worth it, cuz for 6k you'll get hydraulic disc and lockout shocks w...

R. Hertz33

Hey guys, I have a 2012 ranger, and I changed by rims again, however I seem to need hub centric rings. The bore on the rim is 108mm and the hub is 93.1mm. Where can I get these to buy. Has anyone here out fuel rims on a 2012? if so where you got it, if you have it at all. The lugs im using are acorn...

R. Hertz33

I would strongly advise that you do not do anything with this van outside of the firm (hoping that you bought it through McEnearny) because you would void the warranty. I've had mine since February last year and my boost sensor went, for which they ended up replacing the entire turbo unit since they...

R. Hertz33

This is not true and simply a rumour, you are required to have a heavy T liscense to operate the new ford ranger 2.2 due to the MGW

R. Hertz33

half price sale

R. Hertz33

As the topic says, this came off a TBO 4x2 look-a-like frontier

Injector Pump: $6000
Turbo and intercooler:$3500

very negotiable

685-1573

R. Hertz33

you can change the torsion bars - check out 4x4parts.com the american version of the frontiers are the same minus the v6 gas engine which they had to use instead of the diesel engines we get to comply with the emission standards

R. Hertz33

hi guys so i have a TBO 4x2 frontier (high end with the YD25) and the engine was started giving a loud slapping noise. this turned out to be the piston. the van has been down a while as i sent it to rebuild, but long story short, during this time, two of my colleagues experienced the exact same prob...

R. Hertz33

did anyone put this in a d22 frontier 4x2 ie the one with the yd25? what i would like to know is would the existing gearbox of the d22 (4x2) bolt on and work with a qd32? my yd25 failed and im persuing my options, so far nothing but positive reviews on the qd32 except that i wont get a floor shift g...

R. Hertz33

All i wanted, was to work offshore on a rig, and be a 6-footer.
i acheived neither!
now all i am is an electrical engineer who sells valves for a living and I'm 5' 8"

*sigh*

R. Hertz33

just a quick point to note when using the epi, the gains on your amplifier should be set to set at the lowest possible value, since, with the lower frequencies now being input, the system model changes, and as a result the previously used gain can now cause system instability(clipping) therefore sen...

R. Hertz33

well the spring is cheap, and it should cost less than what i paid if you go by your own mechanic. but as for how long it lasts, well as i said mine was done about a year ago and no probs. i also know the cause that resulted in the breakage of my spring ( going in dex, mashing the brakes while keepi...

R. Hertz33

where can you get hawk brake pads for a b14 (front) and also at what estimated cost?

R. Hertz33

i heard that some of those trucks that come down here are LHD and they convert to RHD down here, by some guys who were factory trained, but i belive those trucks are factory designed to accomodate both, so its just a matter of assmebly. i can NOT validate my source though

R. Hertz33

R. Hertz33

i drive a b14 myself and had a similar problem. my problem was that it jerked VIOLENTLY from 1st into 2nd but it was all the time, not some-time-ish like yours. The fix: a spring is broken insider your transmission which costs a measly 75$ however to change this they need to take down your tranny. i...

R. Hertz33

Well please delete then..

R. Hertz33

And I now make a thread wondering why :s

R. Hertz33

Whappning here???????

R. Hertz33

using Mplab, u can run a compiler and program it using C, which is wayyyy easier than assembly, but depending on exactly what u want done, u might have to use the assembly. u sure not just in elec and want somebody to do ure project for u?

R. Hertz33

using Mplab, u can run a compiler and program it using C, which is wayyyy easier than assembly, but depending on exactly what u want done, u might have to use the assembly. u sure not just in elec and want somebody to do ure project for u?

R. Hertz33

using Mplab, u can run a compiler and program it using C, which is wayyyy easier than assembly, but depending on exactly what u want done, u might have to use the assembly. u sure not just in elec and want somebody to do ure project for u?

R. Hertz33

had a 910 bb and when braking from 60kmph used to get a wobble, turned out to be the bushings. after they were changed the problem was gone, same tyres n suspension. but my wobble was from braking

R. Hertz33

my two cents would be to bring small, medium n large, cuz if men hadda wear the small, it means they just small, so n extra small or small wont make much of a diff, but a kinna buffer guy could still squeeze into a small (140lbs @ 5'8") as for the large, well these kinna shirts are supposed to fit p...