Forums

insanelunatic

jusrocky wrote:727-6259
Exclusive designs
Call for advice

Thanks

insanelunatic

Good day. Have a 2015 h100 and would to know if any one ever remove the finisher to change the deck. If so how to. It's a diy system. And really don't wanna break any clips. Thanks.

insanelunatic

dunno if this the right forum for this question.... wanna bring down couple body parts for my suzuki vehicle through YAHOO.jp.auction but cant seem to complete signing up on yahoo that is..... anyone ever gotten through with buying stuff from them?

insanelunatic

still happening nestor?

insanelunatic

nervewrecker wrote:If you have a device to control the output level, it will allow you to adjust your output to suit you.

understood and point taken.... but doing so wouldnt be taking away from the units true potential by lowering the output..?

insanelunatic

much appreciated roach...... just saw men used 1 10" with a the 2" drivers nah and figured how most people says two 12" will out perform one 15" in SUBS that is... was just using the same concepts.... debatable though!! so i ASSUMED my two 8" per big driver may have tied in ...

insanelunatic

need some advice here thanks.... have 1 pair RCF paper cone and 1 pair older model 18sounds 8" have perfect or more power for them with strong amps... which is a better match and not over power my 8z between pair of RCFn850 or selenium 3305... note::: mids will not be built n flare boxes..

insanelunatic

no mechanics on board.....

insanelunatic

just some clarity please..... changing crank and cam seals... marked the top and bottom pullies with a point on the block..... seems as though while relaxing the belt to remove the cam pully came out of place by and inch but the crank didnt move.. should i put back the cam pully inplace or simply li...

insanelunatic

wow! hard to get an input for this......

insanelunatic

to be installed in a mazda B2500 where space is very limited...... wanted to build a ported box and fibreglass the back so as to get the proper specs...... thing is the speaker seems like it works best in a seal box and was NOT recommended in a vented application..... most sites i check really recom...

insanelunatic

good day fellows.... in d route of running a three amp system and wanted to know if what i have will work appropriate..... i have two sx500.2 wanting to run a pair of rcf 8s and a pair of selenium d2500ti(80rms) on each amp and hopefully it will do d job....or shud i run just run d RCF alone on both...

insanelunatic

ng357 wrote:Try launching at a slightly lower rpm.

hmmmm!! will give it ah try....

insanelunatic

3stagevtec wrote:Components have superior designed passive crossovers. Most coaxials are very basic in design. Components all the way..

no doubt bro.....but heard some DDz coax and they where very impressive and the price wasnt dat bad..

insanelunatic

Ted_v2 wrote:Go with the jbl coaxial. They are two ohm. Get full power from your amp

mmmmm!! which model u speak of bro?

insanelunatic

thanks fellers.....good to know.. now i know which direct to take

insanelunatic

iam considering a system that consist of four pairs of either comps or coax 6.5" 4ohm both @ 50/200rms/peak the amps spec reads 130x4 @2ohm and 80x4@4 ohms I was told that the amp will play the coaxial perfect but may not do the same as for the components because of the passive x-over and tweet...

insanelunatic

y so much hating goin on over my lil topic.... man ka be happy he get ah BNIB 9835 in dis present time... Anyhow... realise dis deck have real potential been EQ and Xover purposes.... i have ah KX3 install along with ah us amp 4300x and my past 9811 which didnt have 90% feature as d one i have now.....

insanelunatic

OFFSURE!!! dats close enuf....

PIMP!!! muss say....

insanelunatic

how much would u pay for one of d SWEETEST alpine HU ever made...

insanelunatic

jus ah lil sum sum!!

insanelunatic

:lol: he spammed a bunch of Suzuki type threads asking for J20a parts, then when I removed the posts and messaged him about it, he got upset and posted that afterwards. oh hoo!! thanks HOOK.... and CINCO like 3 months ago.... its jus really weird Only wen I attempt to release off clutch quickly as ...

insanelunatic

huh!! I lost between dem two last comments :s bump never d less....

insanelunatic

so I recently changed clutch, pressure plate and pilot bearing.... I shaved the flywheel slightly, after market clutch disc and OEM pressure plate.... didn't change release bearing doh, it seamed fine no sound when I spun it.. vehicle changes gears smoothly and grabs good with no slippage while driv...

insanelunatic

nervewrecker wrote:gremlins in the electronics.

LMAO...... dats some funny sheit, but tru!!

insanelunatic

problem solved!! dunno how it happened but 1 of the RCA jacks (interfire) sheit...... broke off the back of my alpine deck and I guess It was touchn slightly..... new RCA (DBlink) and worx perfect again... thank GOD it wasn't my amps... thanks for all d inputs fellers

insanelunatic

thanks fellers......great info.....btw...know of a "reliable professional technician" its an an old skool 4300x us amp... dnt want ne novice digging up in it. much thanks!!

insanelunatic

if one of your front channel in ah 4 channel is playing low and i think iam hearing a slight distortion, what does that mean? the other front channel is playing really loud and clean.... note that the gain was left as is when testing both channels... thanks

insanelunatic

Due to the length of time, if it is pas 100K km especially it would not hurt to change the transmission filter. Be sure to get your hands on some silicone to place on the Oil Sump pan. Clean off the magnet and any excess of sealant that may already be there so that it seats properly when you are mo...

insanelunatic

yoooo!! don't no if this topic was talked about but here I go....... willing to do ah DIY auto transmission fluid change on my car after a very very very long time *ashamed* any how, learnt ah bit that its not to hard to drain and refill, but due to the length of time I waited to change was wonderin...