Forums

scoobert_doo

What's the procedure to apply for a taxi badge?

scoobert_doo

Would the primera complete shock and spring bolt up on a b14?

scoobert_doo

Well the car used to be ph but I using it for personal use now that big bounce every time Go over a speed bump or something is annoying....

scoobert_doo

How can I stiffen the back of my b14, I bought complete shock and spring and it was still bouncing to much then I bought new shocks same bounce...how can I stiffen the ride in the back and raise it ?

scoobert_doo

whats a good upgrade for my b14 front brakes?

scoobert_doo

bumppp

scoobert_doo

How to remove b13 automatic shifter?

scoobert_doo

looking for a ga15/16 timing chain kit, i have an engine with a damaged and rattling timing chain, i already changed the head and block but id like to try and change the timing chain and gaskets myself just for the experience....can someone tell me where i can get them?

scoobert_doo

looking for help with my 4d56t engine, fedup with my present mechanic....looking for someone who can tell me whats wrong with my engine, i recently had my engine rebuilt .....sent the block to the machine shop to sleeve and what not .....had it put back together.....and its not performing as it shou...

scoobert_doo

looking for a 4d56t head and block to buy urgently, anyone have one to sell??

scoobert_doo

looking for a 4d56t head and block, my crank shaft bearing and #4 piston gone.....dont have time to take to machine shop.....anyone have a good one to sell?

scoobert_doo

anyone know where i can go to get an estimate on doing a height lift on my k74t l200?
average cost? and a good shop that can do it.

scoobert_doo

im trying to isolate a problem....this is what happens, the temperature gauge stays at half or just below, but the thermometer goes up to 50 sometimes, and when the ac is on it only blows cold when the car is in motion or at night when its not so hot, once im at idle it gets warm.

scoobert_doo

Would there be any issues if I removed the thermostat from my 4d56 engine in my k74 l200?

scoobert_doo

I was considering it because I get a rise in temperature when the van is at idle especially with the ac on...... When it idles with the ac on the the ac blows warm until the vehicle starts moving..... I cleaned the radiator Fins and the ones on the evaporator.... No dice.... The heat just builds up ...

scoobert_doo

im thinking of ordering 2 mishimoto 12 or 16 high flow race line fans, and their fan controller as well, would those be sufficient for the conversion?

scoobert_doo

I'm looking for a specialist more or less to run through my 04 l200 hearing lots of Klunks from the back when the weight is shifting and some annoying noises from the front. Can anybody give a recommendation?

scoobert_doo

hello all, i own a 2005 mitsubishi k74 l200 and im considering removing my clutch fan and install 2 electric fans, is this a good idea? can i damage my engine by doing this? any imput would be greatly appreciated.

scoobert_doo

i have a k74t and im considering changing from clutch fan to electric........can anyone say if this is a good idea or not?

scoobert_doo

Anyone know where I can purchase the internal fuse box for the 2004 l200, I really only need the etac module that goes on the back of it, mine has gone bad and my central locking has gone buggy, and I don't feel like wiring relays in my doors. ... But I doubt I'll get it to buy alone... Any informat...

scoobert_doo

is it possible to move the oil cooler on the k74? id like to move mine from the front of the condenser and put it lower......if possible with an aftermarket oil cooler, id appreciate any help or information.

scoobert_doo

Hi everyone..... I'm looking for someone who can repair my k74 l200 suspension.... Lots of noises and my present mechanic not really familiar with it. I'm also looking for a roll bar for the back and the original bull bar for the front.

scoobert_doo

Anyone have a set of leaf Springs for the 05 l200, preferably the 6 leaf?

scoobert_doo

The size of the intercooler inlet and outlet are smaller on the non turbo, also the number of valves differ.... I think the turbo has an extra valve.

scoobert_doo

Will this work on my 4d56t? Im concerned about the gap between the spring device and the hole below it.

scoobert_doo

Got it from nickolas in charlieville, he has plenty 4x4 parts

scoobert_doo

This is the oil filter housing I bought for my l200....is that spring plunger suppose to block the hole it's over or is there supposed to be a space between the bottom of the plunger and the hole?? Someone please help......

scoobert_doo

Anyone here with the k74t, l200 with the 4d56 engine? I'm looking for the oil filter housing..... The part where the oil filter and oil sensor attach to.... Can anyone help me locate one I need it urgently

scoobert_doo

Can anyone tell me where I can get the oil unit for a k74 4*4 l200, I'm also looking for the two oil lines that go right above the oil unit on the right..... The oil unit just stared leaking and lots of oil leaked out..... And while checking it I noticed the lines were wet with oil as well...