So it's 2025 and the extractor kit is still on and still going but finally it's time to change it cause it has gitten very thin and the hissing is too loud now....the material was too thin ( being aftermarket )
Looking for someone to build a good extractor for me now... possibly 4 into 1
The rear rotors are even bigger by about an inch in diameter The rears...they are exactly the same hubs but obviously the p12 are 5 lug.Unbolt the usdm caliper and bolt the jdm one on...no problem. Heres our spindle http://i46.photobucket.com/albums/f139/jgauspohl/p11spindle.jpg heres the p12 http:...
This project is awesome! We have to start building these fellas. http://www.g20style.com/Quad%20projector%20project.htm http://www.g20style.com/dual%20projector%20PS.jpg http://i46.photobucket.com/albums/f125/timscivic/Infiniti/Retrofit/Retro5.jpg http://i46.photobucket.com/albums/f125/timscivic/In...
speedfreak44 / swift git funatic - I saw that but I was trying to see if there was any other Nissan suspension that would have lined up without changing anything. This way we would have had another way to do it. It's always good to experiment cause you never know when you might come up with a simple...
The rear rotors are even bigger by about an inch in diameter The rears...they are exactly the same hubs but obviously the p12 are 5 lug.Unbolt the usdm caliper and bolt the jdm one on...no problem. Heres our spindle http://i46.photobucket.com/albums/f139/jgauspohl/p11spindle.jpg heres the p12 http:...
ok...not so good news...P12 rear suspension does not match up. Did some measurements and the banjo is longer but the space between the arms that bolt onto the body are wider :-( But.... I was told that it could be done but I'll have to use the hub, spindle from another vehicle :-) The drama continue...
so the spindles bolt on direct? yes also wat is the wheel nut spacing is it 5x114? yes and the brake set up the same as the p11 also the axles? u will be using your axles i want to know going to try this conversion someday and want to know what i have to get? Ok now this is the sort of feedback I w...
so the spindles bolt on direct? yes also wat is the wheel nut spacing is it 5x114? yes and the brake set up the same as the p11 also the axles? u will be using your axles i want to know going to try this conversion someday and want to know what i have to get? Ok now this is the sort of feedback I w...
Guys - what do they call this joint that is exposed at the bottom of the pic that supposedly has a bearing inside it? Can the bearing itself be replaced, or do I need to get the whole damn arm? If so, where can I look for it, without having to take it out to walk with it to the parts place? Also - ...
Ok I hear you... The way it's written it's as though 1600-1799 cc from $4 to $8 per cc meant that it ranges from $4 to $8 dollars when it should have said 1600-1799 cc went from $4 to $8 per cc
May be the flex joint itself. I get an annoying raspy hiss type noise from mine on my Mazda. Noise was lessened by moving the joint down the piping but you can only move it so far. Agreed. I was thinking about doing that as well, but I'll have to wait until w/end again to pull it off myself and see...
Reason for asking is that I installed a one a few years ago that I bought from a fellow Tuner ( the complete EXTRACTOR, FLEX JOINT, DOWN PIPE etc. ) and the hissing noise was not too prominent then as it is now. Now when I'm accelerating I'm getting a pretty irritating " Hissing " noise co...
^^^^ so i'm taking it that the above calculations are the current ones ? Cause what is not making sense here is that in the past we had category ranges for the CCs and a specific rate for anything in that bracket, for example: 1600 to 1798 - $8.00 per cc 1799 to 1998 - $15.00 per cc Now we have: 160...
Was asking cause I'm having the same problem I took out my stock manifold and replaced it with an extractor kit...The cat-convert was taken out, the old barrel was replaced with a fujitsubo barrel that came off an S14 and there's a resonator. I was told to go check a guy not too far from Roopnarines...
