Moderator: 3ne2nr Mods
Using the amp. Everything flat or off on the deck. Thing is, is trial and error in getting the speaker just right especially at high volume.nick639v2 wrote:What you using to set crossover levels? Head unit or amp??
500hz boy, yuh wasting d speaker inno
fatboy slim wrote:pioneer 80 prs
kavaninho wrote:fatboy slim wrote:pioneer 80 prs
Not even this. The newer lower end pioneers are cheap and have great DSP capability, similar the the PRS but not as extensive as.
S5000btVexXx Dogg wrote:kavaninho wrote:fatboy slim wrote:pioneer 80 prs
Not even this. The newer lower end pioneers are cheap and have great DSP capability, similar the the PRS but not as extensive as.
Yea?
I need a replacement for meh old van. I just about ready to pelt the 149BT away.
What's good?
Wish i cud, but dvd deck to accommodate back up camera for wifey and to keep me occupied when i waiting for her after classesfatboy slim wrote:pioneer 80 prs
SYKO wrote:Guys straying from my topic a bit here. My mids amp is a soundstream tn4.900, with a pair of loudforce drivers and a pair of B&C 8".
Currently wired
Ch 1 - driver
Ch 2 - driver
Ch 3 & 4 bridged - speakers.
Is this ideal to get the most out of the amp ?
Or shud i do
Ch 1 & 2 speaker and driver (with resistor)
Ch 3 & 4 same?
Its the 8" pe21. So basically switch around the wiring and add the mentioned resistor. Will play around with it and see. Thanks88sins wrote:SYKO wrote:Guys straying from my topic a bit here. My mids amp is a soundstream tn4.900, with a pair of loudforce drivers and a pair of B&C 8".
Currently wired
Ch 1 - driver
Ch 2 - driver
Ch 3 & 4 bridged - speakers.
Is this ideal to get the most out of the amp ?
Or shud i do
Ch 1 & 2 speaker and driver (with resistor)
Ch 3 & 4 same?
since no sub on the amp & u eh say what b&c 8"
wire b&c's in parallel to ch 1-2 bridged with a 22uf condenser.
same wiring for ch3-4 with the drivers, but only if in parallel they not below 4 ohms.
Is for wen i home or liming with my co workers. Once it loud and not distorted we good to go.Rovin wrote:how much more ole noise u want , i wuda leff it as is ...
So I cud tell men daz only on volume 10 outta 50 boy.. I still have real powerRovin wrote:^^^care to explain that HU vol 50% suggestion , what u leaving back d remaining 1\2 of d vol level to do ?
find a reputable shop with a O scope or SMD DD1 to set ur gains , for crossover points : SMD CC1
or there are numerous vids on youtube on how to set gain with a DMM
as for setting ur EQ : u set it to ur personal taste , try not to over boost stuff ... imo : less is more
nick639v2 wrote:So I cud tell men daz only on volume 10 outta 50 boy.. I still have real powerRovin wrote:^^^care to explain that HU vol 50% suggestion , what u leaving back d remaining 1\2 of d vol level to do ?
find a reputable shop with a O scope or SMD DD1 to set ur gains , for crossover points : SMD CC1
or there are numerous vids on youtube on how to set gain with a DMM
as for setting ur EQ : u set it to ur personal taste , try not to over boost stuff ... imo : less is more
Return to “I.C.E. / Car Audio Tech”
Users browsing this forum: No registered users and 20 guests